BS EN 1852-1-2009 Plastics Piping Systems for Nnpressure Underground Drainage and Sewerage
|
ID： |
1E7BC1789EA1420CB335B93561A3028D |
|
文件大小(MB)： |
1.37 |
|
页数： |
38 |
|
文件格式： |
|
|
日期： |
2009-5-13 |
|
购买： |
文本摘录（文本识别可能有误，但文件阅览显示及打印正常，pdf文件可进行文字搜索定位）：
BS EN,1852-1:2009,ICS 23.040.01; 23.040.20; 93.030,NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW,BRITISH STANDARD,Plastics piping,systems for nonpressure,underground,drainage and sewerage,— Polypropylene (PP),Part 1: Specifications for pipes, fittings,and the system,This British Standard,was published under the,authority of the Standards,Policy and Strategy,Committee on 30 April,2009,. BSI 2009,ISBN 978 0 580 58894 5,Amendments/corrigenda issued since publication,Date Comments,BS EN 1852-1:2009,National foreword,This British Standard is the UK implementation of EN 1852-1:2009. It,supersedes BS EN 1852-1:1998 which is withdrawn.,The UK participation in its preparation was entrusted to Technical,Committee PRI/88/1, Plastics piping for non-pressure applications.,A list of organizations represented on this committee can be obtained on,request to its secretary.,This publication does not purport to include all the necessary provisions,of a contract. Users are responsible for its correct application.,Compliance with a British Standard cannot confer immunity,from legal obligations.,BS EN 1852-1:2009,EUROPEAN STANDARD,NORME EUROPéENNE,EUROP腎SCHE NORM,EN 1852-1,March 2009,ICS 23.040.01; 93.030 Supersedes EN 1852-1:1997,English Version,Plastics piping systems for non-pressure underground drainage,and sewerage - Polypropylene (PP) - Part 1: Specifications for,pipes, fittings and the system,Systèmes de canalisations en plastique pour les,branchements et les collecteurs d'assainissement enterrés,sans pression - Polypropylène (PP) - Partie 1 :,Spécifications pour tubes, raccords et le système,Kunststoff-Rohrleitungssysteme für erdverlegte drucklose,Abwasserkan鋖e und -leitungen - Polypropylen (PP) - Teil,1: Anforderungen an Rohre, Formstücke und das,Rohrleitungssystem,This European Standard was approved by CEN on 14 February 2009.,CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European,Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national,standards may be obtained on application to the CEN Management Centre or to any CEN member.,This European Standard exists in three official versions (English, French, German). A version in any other language made by translation,under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the,official versions.,CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.,EUROPEAN COMMITTEE FOR STANDARDIZATION,COMITé EUROPéEN DE NORMALISATION,EUROP腎SCHES KOMITEE FüR NORMUNG,Management Centre: Avenue Marnix 17, B-1000 Brussels,. 2009 CEN All rights of exploitation in any form and by any means reserved,worldwide for CEN national Members.,Ref. No. EN 1852-1:2009: E,BS EN 1852-1:2009,EN 1852-1:2009 (E),2,Contents Page,Foreword .. 4,1 Scope 5,2 Normative references . 5,3 Definitions, symbols and abbreviations . 6,3.1 Definitions .. 6,3.2 Symbols .. 8,3.3 Abbreviations . 9,4 Material 9,4.1 PP compound 9,4.2 Reprocessable and recyclable material . 10,4.3 Melt mass-flow rate .. 10,4.4 Resistance to internal pressure . 10,4.5 Thermal stability (OIT) 11,4.6 Sealing ring retaining means .. 11,5 General characteristics .. 11,5.1 Appearance . 11,5.2 Colour . 11,6 Geometrical characteristics . 12,6.1 General . 12,6.2 Dimensions of pipes . 12,6.2.1 Outside diameters .. 12,6.2.2 Outside diameters with close tolerances (CT) . 12,6.2.3 Length of pipes . 13,6.2.4 Chamfering . 14,6.2.5 Wall thicknesses . 14,6.3 Dimensions of fittings .. 15,6.3.1 Outside diameters .. 15,6.3.2 Design lengths . 15,6.3.3 Wall thicknesses . 16,6.4 Dimensions of sockets and spigots.. 17,6.4.1 Diameters and lengths of elastomeric ring seal sockets and spigots .. 17,6.4.2 Wall thicknesses of sockets .. 19,6.5 Types of fittings .. 20,7 Mechanical characteristics .. 23,7.1 Mechanical characteristics of pipes . 23,7.1.1 General requirements .. 23,7.1.2 Additional mechanical requirements . 23,7.2 Mechanical characteristics of fittings .. 24,8 Physical characteristics . 24,8.1 Physical characteristics of pipes 24,8.2 Physical characteristics of fittings . 25,9 Performance requirements .. 25,10 Sealing rings . 26,BS EN 1852-1:2009,EN 1852-1:2009 (E),3,11 Marking . 26,11.1 General .. 2……
……